Providence Natural Grey RTA Kitchen Cabinets

Providence Natural Grey 36x96 Finished Back Panel
SKU# FBP369614-1-TS

Width 36" | Height 96" | Depth .25"
Finished back panel. Commonly used to finish the back of an island. Grain will run vertically (along the height) and the panel will be finished on one side.

$348.26

Qty
Providence Natural Grey 48x36 Finished Back Panel
SKU# FBP483614-1-TS

Width 48" | Height 36" | Depth .25"
Finished back panel. Commonly used to finish the back of an island. Grain will run vertically (along the height) and the panel will be finished on one side.

$227.27

Qty
Providence Natural Grey 48x96 Finished Back Panel
SKU# FBP489614-1-TS

Width 96" | Height 48" | Depth 0.25"
Finished back panel. Commonly used to finish the back of an island.

$364.99

Qty
Providence Natural Grey Bead Board Panel
SKU# BP48341214-TS

Width 48" | Height 34.5" | Depth 0.25"
Beaded board panel. Commonly used to give a beaded finished look.

$295.89

Qty

Shipping Time:	Shipped in 5-15 business days
Style:	Recessed
Face Frame:	3/4" Solid Wood
Door Frame:	3/4" Solid Wood
Door Center:	MDF w/Wood Veneer (MDF is used to avoid cracking/warping)
Sides:	1/2" A-Grade plywood with wood veneer
Top & Bottom (Wall):	1/2" A-Grade plywood with wood veneer
Bottom (Base):	3/8" A-Grade plywood with wood veneer
Back Panel:	Wall Cabinets: 1/2" Picture Frame Recess Style, Base Cabinets: 1/2" Full Back
Shelves:	3/4 " A-Grade plywood with wood veneer
Base Cabinet Shelf Depth:	1/2
Drawer Box:	Solid Wood 17mm (close to 3/4") sides, Drawer bottom 1/2" plywood, Drawer length 21". Dovetail construction, Natural finish.
Drawer Glides:	Undermount, full extension with soft closing feature
Base Corner Supports:	Wood corner brackets with wood I-beam construction
Overlay:	Full with Butt doors
Hinges:	Concealed 6-way adjustable with Soft Closing Feature
Cabinet Interior:	Matches door finish
Center Stile:	No center stile on cabinetry 24"W to 36"W
Assembly Method:	Steel Clip
Finish:	Waterborne UV finish by Sherwin-Williams
Toe Kick:	1/2" Plywood (sides of the toe kicks will be unfinished)
Installation Rail:	1/2" Plywood
Wall Cabinet Bottoms Finished (Exterior):	Yes
KCMA Compliant:	Yes
CARB Compliant:	Yes
Door Hinges:	Hinged To The Right By Default. For Wall Cabinets The Face Frame Can Be Flipped. For Base Cabinets Unhinge The Door, Flip It, Screw Holes On The Opposite Side To Re-Hinge, And Then Fill The Original Holes (Touch Up Kit Can Be Purchased For This)
Toe Kicks Included w/Base Cabinets:	Yes
Sides Panels Finished:	Yes
Installation/Design Note:	The full-overlay door style leaves roughly a 1/4" clearance on the edge. If installed directly against a wall or deeper cabinet and a cabinet door opening of at least 90 degrees is desired, scribe molding should be installed between the cabinet and the wall (or deeper cabinet). If not, the door may not be able to open a full 90 degrees. For a full opening, a space of at least 1/4-1/2" is necessary, a larger space may be needed depending on the decorative hardware used on the cabinets. The cabinet depth measurement listed is the depth from the front of the face frame to the back of the cabinet, and does not include the cabinet door depth. Cabinet specs are subject to change without notice. Cabinet measurements are typically converted from metric to inches and manufacturers will commonly round up to the nearest 1/4 inch. This can cause a measurement to be off by a fraction of an inch (less than 1/4") which is within normal industry standards Schematic imagesand renderings are generic and may not represent exact construction details for each collection. The exact specificationsforthis collection can be found in theconstruction detailslisted above.

Providence Natural Grey

Get Help

Thank you!